“I am impressed by Lako’s continuous dedication to research and design for customer-specific applications. I presented Lako with the opportunity to help my company find a mechanical solution to an industry-wide problem — air retention in gusseted bags that are packed lying down in the case. They researched and designed four specific jaw serration patterns to test in the lab with different film structures, temperatures, sealing times and pressures to identify the optimal jaw set. Although this was not implemented due to a different business priority, it was a thorough feasibility study.”
- Meagan Reid, The Hershey Company
“I am impressed by Lako’s continuous dedication to research and design for customer-specific applications. I presented Lako with the opportunity to help my company find a mechanical solution to an industry-wide problem — air retention in gusseted bags that are packed lying down in the case. They researched and designed four specific jaw serration patterns to test in the lab with different film structures, temperatures, sealing times and pressures to identify the optimal jaw set. Although this was not implemented due to a different business priority, it was a thorough feasibility study.”
- Meagan Reid, The Hershey Company
“I am impressed by Lako’s continuous dedication to research and design for customer-specific applications. I presented Lako with the opportunity to help my company find a mechanical solution to an industry-wide problem — air retention in gusseted bags that are packed lying down in the case. They researched and designed four specific jaw serration patterns to test in the lab with different film structures, temperatures, sealing times and pressures to identify the optimal jaw set. Although this was not implemented due to a different business priority, it was a thorough feasibility study.”
- Meagan Reid, The Hershey Company
-
LED Control Display Offfor HCP Punch and Digital Controller Power Switch at OFF position Power cord not plugged Power outlet OFF or NO power out 0.5 Amp hot punch controller fuse burn out Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
Punch Heater Not Working / SUB 2 Alarm LED Light Indicator ONfor HCP Punch and Digital Controller Hot punch Amphenol connector not connected 1.25 Amps fuse burn out for 150 watts hot punch 2.5 Amps fuse burn out for 250 watts hot punch 4.5 Amps fuse burn out for 500 watts hot punch Hot punch heater wires disconnected from male Amphenol connector Hot punch heater failure Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
LED Screen Shows SERR Codefor HCP Punch and Digital Controller Hot punch Amphenol connector not connected to the controller TC or RTD sensor wire disconnected from male Amphenol connector TC or RTD sensor failure Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
SUB 1 Alarm LED Light ON /Auto Tune HI/LO Indicator Light ON or Both Flashingfor HCP Punch and Digital Controller Do auto tune to the hot punch controller (Please follow auto tune procedures) The PV (point variable) temperature lower or higher then SV (set variable) temperature (Our factory default deviation is 5 degree for both HI /Low alarm) Adjust the SUB 1 alarm temperature deviation by setting the alarm upper limit (H) and Alarm lower limit (L) to the prefer value up to your application temperature alarm requirement (read quick punch temperature control setup guide) Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
SUB 2 Alarm LED Light Indictor ON Hot Punch Situation Is Hotfor HCP Punch and Digital Controller Hot Punch temperature PV (point variable) lower than the SV (set variable). Our factory default downward deviation is 10 degree below the SV (Set variable). Adjust the SUB 2 alarm downward temperature deviation by setting the alarm lower limit to the prefer value up to the application temperature alarm requirement, (read quick punch temperature control setup guide) Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
Hot Punch Controller Function Stop /STOP LED Light Indicator ONfor HCP Punch and Digital Controller HOT punch controller at STOP MODE. Switch the program Mode from STOP to RUN (read quick punch temperature control setup guide) Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
Premature knife wear?Always change the anvil when changing the knife. Still experiencing a challenge? Please contact our office. Email: inquiry@lakotool.com Phone: +1 (419) 662-5626
-
Better SealFor better seals... Always keep the seal form knife and anvil free of debris
-
Enter your answer here